The MMTCPDIOAIO module is a multipurpose combination of inputs and outputs. The module can accommodate either 2 or 3 wire RTD sensors, current (0-20mA) and voltage (0-10V) inputs, current (0-20mA) or voltage (0-10V) output, and digital inputs and outputs. 

RTD INPUTS:

There are 2 RTD inputs on the module. The RTD resistance is read by the module circuitry, linearised and converted to degrees Centigrade. No ranging is required as the module covers the full range of the RTD as indicated in the RTD table.  The value that is read from the Modbus register is the actual temperature in degrees centigrade to 0.1°C resolution. ie: a value of 3451 corresponds to a temperature of 345.1°C. 

The RTD type is setup by writing a value to the RTD Type register. The value is obtained from the table below. For example to select a PT100 RTD, the value "1" must be written to the RTD Type register. 

A value of -32767 is used to indicate downscale burnout. 

Note: As there is no inter-channel isolation, isolated RTD's must be used in order to prevent ground loops and reading errors. 

ANALOG INPUTS:

The Analog Inputs (2) can be configured by internal jumpers as either a current input (0-20mA) or a voltage input (0-10V).  

An input of 0 - 20mA input current or 0 – 10V input voltage represents an output value of 0 - 4095 (12 bits) in the corresponding Modbus register. 

ANALOG OUTPUT:

There is a single analog output which can be configured with internal jumpers for a current output (0-20mA) or voltage output (0-10V). 

The resolution is 12 bits, so writing a value to the Modbus register for each output  of 0 - 4095 would give an output current of 0 - 20mA. A value of 819 ± 1LSB will give a current output of 4mA. 

DIGITAL INPUTS:

There are 5 digital inputs on the module. The inputs have internal pull-up resistors and are switched to negative. 

The first 2 inputs have got counters associated with them. The counters operate in three modes. 

In mode 0 all the counters are disabled. 

In mode 1 all counters are 32 bit counters allowing a count value from 0 to 4294967295. The count value can be cleared by writing a zero to the associated registers or preset to any other value using the same method. 

In mode 2 the inputs are connected as up/down counters. Input 1 will increment counter 1 whilst input 2 decrements counter1. 

Note: The count values are not battery backed-up and will be lost if power is turned off. 

The format of the registers allows the status of the inputs to be read as either single bits or all at once as a single register on the Modbus network. 

DIGITAL OUTPUTS:

The module has 2 open collector (NPN) digital outputs. The outputs may be used to drive lamps or external relays when more drive capability is required. 

The outputs are written to by the Modbus master device such as a PC or PLC. Each output can be individually switched on or off, or all outputs can be set up at the same time by writing a single number to the output register which represents the status of all outputs. 

An output watchdog timer can be configured to switch off all the outputs if there has been no communications with the module for up to 255 seconds. A value of 0 seconds will disable this timer and the outputs will remain in the last programmed state.

Each MMTCPDIOAIO Module has a unique Ethernet IP address which must be programmed into the PC or PLC. The IP address in the MMTCPDIOAIO Module is configured via the Web Server. Any standard Web browser such as Internet Explorer can be used to access the web pages were configuration is carried out. The converters are factory programmed with a default IP address of 169.254.111.111. This address must be changed before the converter is added to an existing network. 

The web page address for viewing the input/output status parameters is http://169.254.111.111/index.htm  and the address for viewing the configuration is http://169.254.111.111/tconfig.htm.

The web page address for configuring the module is http://169.254.111.111/ip.htm .

Send mail to proconel@proconel.com with questions or comments about this web site.